Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Technyl® eXten D 218 V30 - PA610-GF30 - DOMO Engineering Plastics

Check here, which other Technyl eXten datasheets, application examples or technical articles are available in Material Data Center

Processing/Physical Characteristics - Mechanical properties - Thermal properties - Other properties - Diagrams

Any use of this information falls under the rules of our disclaimer.

Product Texts

 TECHNYL® eXten D 218 V30 is a 30% Glass Fibre reinforced and heat stabilised product suitable to the

manufacturing of all injection moulded parts.

Processing/Physical Characteristics	dry / cond	Unit	Test Standard
ISO Data
Molding shrinkage, parallel	0.4 / *	%	ISO 294-4, 2577
Molding shrinkage, normal	0.5 / *	%	ISO 294-4, 2577

Mechanical properties	dry / cond	Unit	Test Standard
ISO Data
Tensile Modulus	8500 / 6100	MPa	ISO 527
Stress at break	152 / 112	MPa	ISO 527
Strain at break	4.5 / 7.5	%	ISO 527
Charpy impact strength, +23°C	90 / -	kJ/m²	ISO 179/1eU
Charpy impact strength, -30°C	85 / -	kJ/m²	ISO 179/1eU
Charpy notched impact strength, +23°C	14 / 17	kJ/m²	ISO 179/1eA
Charpy notched impact strength, -30°C	10 / 11	kJ/m²	ISO 179/1eA

Thermal properties	dry / cond	Unit	Test Standard
ISO Data
Melting temperature, 10°C/min	215 / *	°C	ISO 11357-1/-3
Temp. of deflection under load, 1.80 MPa	195 / *	°C	ISO 75-1/-2
Thickness tested	1.6 / *	mm	-
Yellow Card available	yes / *	-	-
Burning Behav. at thickness h	HB / *	class	IEC 60695-11-10

Other properties	dry / cond	Unit	Test Standard
Water absorption	2.1 / *	%	Sim. to ISO 62
Humidity absorption	0.33 / *	%	Sim. to ISO 62
Density	1300 / -	kg/m³	ISO 1183

Diagrams

Characteristics

Processing

Injection Molding

Special Characteristics

Heat stabilized or stable to heat

Certifications

Contains renewable resources

Regional Availability

North America, Europe, Asia Pacific, South and Central America, Near East/Africa

Other text information

Injection molding

The material is supplied in airtight bags, ready for use. In the case that the virgin material has absorbed moisture, it must be dried to a final moisture content less than 0,2% with a dehumidified air drying equipment at approximately 80°C.

 

Recommended moulding conditions:

 

-Barrel temperatures

Feed zone                     225-230°C

Compression zone         230-240°C

Front zone                     240-250°C

.

-Mould temperatures         80-100°C

Chemical Media Resistance

Acids
	Acetic Acid (5% by mass) (23°C)
	Sulfuric Acid (38% by mass) (23°C)
	Sulfuric Acid (5% by mass) (23°C)
Alcohols
	Ethanol (23°C)
Hydrocarbons
	Toluene (23°C)
Ketones
	Acetone (23°C)
Mineral oils
	SAE 10W40 multigrade motor oil (23°C)
Standard Fuels
	Standard fuel with alcohol (pref. ISO 1817 Liquid 4) (23°C)
Salt solutions
	Zinc Chloride solution (50% by mass) (23°C)
Other
	Hydrogen peroxide (23°C)
	Ethylene Glycol (50% by mass) in water (108°C)
	50% Oleic acid + 50% Olive Oil (23°C)
	Deionized water (90°C)
	Phenol solution (5% by mass) (23°C)

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.